Tub spout drips after shower

Tub spout dripping for a while after the shower is turned off.

After shower shutoff, a tub spout can release water retained downstream, or it can receive continuing supply through the flow-control path. Record the rate, taper and location without using a universal minutes-or-milliliters cutoff.

Stop using the fixture for water at the wall, damp ceilings below, an uncontrolled leak or unsafe/unstable temperature. Use a known effective water shutoff only from safe access when no gas is suspected; get prompt plumbing help. Do not run more water to photograph a concealed leak or continue at lower flow with towels as protection.

Keep away from wet electrical equipment. Do not touch wet appliances, plugs or switches, or enter water to reach a breaker. When no gas leak is suspected, power may be isolated only from a safely accessible dry location; otherwise call an electrician or emergency help. Wet equipment needs qualified assessment before it is used again.

Record the original pattern

  • Time since the original use, approximate amount/rate and whether it tapers or recurs without use.
  • Outlet drops versus wall/joint leakage, plus actual valve/diverter arrangement.
  • Recent service and known head/hose/riser layout without another long run.

What the pattern means

A diverter can route retained water without being the control that shuts off fresh supply. In a system with a separate mixing/flow valve, replacing a routing diverter is not automatically the cure for continuing supplied leakage. Finite drainage depends on the actual downstream arrangement.

Identify the selected mode and where water emerges. Limited tub-outlet bypass is permitted on some systems; use the installed model’s guidance instead of requiring every diverted spout to be completely dry. Water rising to a showerhead during tub filling, water at a wall joint and continuing output after the supply control is off are different symptoms. A routing diverter need not be the control that shuts off new supply.

What to do next

  1. Use the intended normal off position without cranking tighter or cycling the diverter to clear grit.
  2. For a minor stable outlet drip with safe access and an accepting tub drain, an attended secured receiver can document amount over a known interval. Keep it from blocking drainage; a measured amount is a clue, not a universal pass/fail limit.
  3. Do not loosen joints, remove a spout or operate one nearby stop as an unqualified source test. Effective all-feed isolation and actual retained water must be considered.
  4. Have ongoing or unclear supplied leakage assessed using the real valve closure and service method. Do not wait a full day to establish the manufacturer’s continuous-leak symptom or choose a cartridge solely from duration.

Before parts work

Before removal or adjustment, find the exact valve, spout and adapter instructions. A missing visible set screw does not prove a direct-threaded attachment. Do not twist a still-secured slip-on spout, force concealed piping, cut a stub to a guessed length or use a flush-looking wall fit as proof the inlet seals.

For pressure-boundary work, isolate every feed that can pressurize the section, control hot-water temperature, relieve the actual work segment through its intended outlet and verify depressurization. A nearby sink tap or stop may not serve or relieve this shower. Secure all required pressure retainers and connections before restoring water; isolate and relieve again before repeat access.

Use the approved part, seals, lubricant, thread treatment, pipe engagement and torque for that exact assembly. Not every threaded-looking joint seals on its threads. Intended owner surface care starts with the fixture off and parts cool, using finish-compatible instructions; do not improvise a vinegar soak, scrape sealing surfaces or remove an unidentified insert. After applicable valve work, complete the model’s measured temperature-protection and leak checks before bathing. Do not move a temperature limit hotter to cure a leak.

When to get help

Get prompt help for wall wetness, uncontrolled water or unsafe temperature; arrange service for continuing supply leakage. Intended finite drain-down and a real shutoff failure need different responses.

Related guides

Safety sources

Find another plumbing guide

Need help with a different area? Choose a topic, then find the guide that matches your symptom.

Browse plumbing topics

Start with the affected area, then choose the guide that matches what happened.